Roll over image to zoom in
Hi-Point Stock
$99.99
Made in the USA
- Made in the USA
- Limited Lifetime Warranty
Fits: Most Hi-Point 9mm Carbine. Does not fit the new Hi-Point 995TS due to manufacturer’s new retaining clips and new receiver shroud. Does not fit the 40 cal. or 45 cal.
Note: Some minor modification may be required.
Original receiver cover barrel bolts are required for installation of stock to all Hi-Point 9MM Carbine models.
- Hi-Point Rifle Stock
- Ergonomic Modern Design
- Textured Grip Area
- Ambidextrous
- Includes Front & Rear Sling Studs
- DuPont® Extreme Reinforced Polymer
- Limited Lifetime Warranty
- Made in the USA
Share your thoughts!
What others are saying
Instructions
Hi point 9mmRated 5 out of 5 4.82
by Greg M.
Nothing bad to say, stock is great! ATI was great !thanks guys
(0) (0)
This is an Excellent Stock for Hi PointRated 5 out of 5 4.82
by Chris B.
This stock is so much better than the original Hipoint stock. Gives the gun the look and feel of the baretta mx4. I purchased this to install on my Hipoint 995TS carbine which the description says it is not made to fit. However, with some work, you can get a great fit and have an sharp looking 9mm carbine for a lot less then the Baretta.
Modifications:
1. Grind out the inner rib to fit the barrel retainer.
2. Grind the imside of the top forgrip to match the contour of the 995TS.
3. Purchase #6 washers and e clips to use the original retaining pins.
4. sand down the back end cover to fit.
I am extremely happy with the finished carbine. Its shorter and easier to maneuver. overall, it just makes the hipoint feel right. I would stronly recommend getting this stock for your Hipoint 9mm.
(0) (0)
This is an Excellent Stock for Hi PointRated 5 out of 5 4.82
by Chris B.
This stock is so much better than the original Hipoint stock. Gives the gun the look and feel of the baretta mx4. I purchased this to install on my Hipoint 995TS carbine which the description says it is not made to fit. However, with some work, you can get a great fit and have an sharp looking 9mm carbine for a lot less then the Baretta.
Modifications:
1. Grind out the inner rib to fit the barrel retainer.
2. Grind the imside of the top forgrip to match the contour of the 995TS.
3. Purchase #6 washers and e clips to use the original retaining pins.
4. sand down the back end cover to fit.
I am extremely happy with the finished carbine. Its shorter and easier to maneuver. overall, it just makes the hipoint feel right. I would stronly recommend getting this stock for your Hipoint 9mm.
(0) (0)
This is an Excellent Stock for Hi PointRated 5 out of 5 4.82
by Chris B.
This stock is so much better than the original Hipoint stock. Gives the gun the look and feel of the baretta mx4. I purchased this to install on my Hipoint 995TS carbine which the description says it is not made to fit. However, with some work, you can get a great fit and have an sharp looking 9mm carbine for a lot less then the Baretta.
Modifications:
1. Grind out the inner rib to fit the barrel retainer.
2. Grind the imside of the top forgrip to match the contour of the 995TS.
3. Purchase #6 washers and e clips to use the original retaining pins.
4. sand down the back end cover to fit.
I am extremely happy with the finished carbine. Its shorter and easier to maneuver. overall, it just makes the hipoint feel right. I would stronly recommend getting this stock for your Hipoint 9mm.
(0) (0)
This is an Excellent Stock for Hi PointRated 5 out of 5 4.82
by Chris B.
This stock is so much better than the original Hipoint stock. Gives the gun the look and feel of the baretta mx4. I purchased this to install on my Hipoint 995TS carbine which the description says it is not made to fit. However, with some work, you can get a great fit and have an sharp looking 9mm carbine for a lot less then the Baretta.
Modifications:
1. Grind out the inner rib to fit the barrel retainer.
2. Grind the imside of the top forgrip to match the contour of the 995TS.
3. Purchase #6 washers and e clips to use the original retaining pins.
4. sand down the back end cover to fit.
I am extremely happy with the finished carbine. Its shorter and easier to maneuver. overall, it just makes the hipoint feel right. I would stronly recommend getting this stock for your Hipoint 9mm.
(0) (0)
Awesome stockRated 5 out of 5 4.82
by Aaron G.
I bought my hi point with this stock. Looks amazing. Feels high quality and makes is look like a bretta. I did see a video of a guy who used this on the newer style and had to modify slightly and it looks good.
(0) (0)
Awesome stockRated 5 out of 5 4.82
by Aaron G.
I bought my hi point with this stock. Looks amazing. Feels high quality and makes is look like a bretta. I did see a video of a guy who used this on the newer style and had to modify slightly and it looks good.
(0) (0)