Strikeforce AK-47 GEN2 Stock

$84.99

Made in the USA

Clear
Compare
SKU: C.2.10.1226 Category:

Fits:

  • Most stamped AK-47 receivers. Will not fit milled receivers.
  • Note: *Will not fit the M-70. (The M-70 has a stamped receiver, but utilizes a different principle of attaching the stock and the gas piston is longer than a standard AK.)

Features:

  • TactLite GEN2 Six-Position Adjustable Stock
    • Side-Folds to the Left of the Receiver
    • Can be Fired from Folded Position
    • TracLOCK GEN2 System
      • Eliminates Horizontal & Vertical Movement of the Stock on the Buffer Tube
      • Provides Smooth Secure Stock Adjustments
      • Eliminates the Need for Secondary Locking Mechanisms
    • Dual Sided QD Attachment Point
    • Removable/Adjustable Cheekrest System
      • Elongated Design to Fit All Users
      • Includes Short Cheekrest with ½” of Adjustment
  • X Series Thin Recoil Pad
    • Non-Slip, Removable
  • Slot for Tactical Sling Attachment
  • All Mounting Hardware Included
  • Extreme Temperature Glass Reinforced Polymer
  • Limited Lifetime Warranty
  • Made in the USA

Available Extras & Upgrades:

Upgrade to the ATI X1 or X2 Recoil Reducing Butt Padd for More Comfort and Length of Pull – A.5.10.2530 & A.5.10.2531

Notes:

Sling Swivel Studs Accepts ATI’s Sling Swivel (Part # A.5.10.2506) or any Standard Sling Swivel

SEC922R: ATI products are manufactured in the USA and count towards compliance parts. Contact your local gun shops or shooting ranges for this and other compliance issues.

Side Folding Stock Note: Your firearm must meet SEC 922R requirements to retain the adjustable buttstock in the folding buttstock configuration. If your firearm does not meet the SEC 922R requirements, you must equip the firearm with a fixed position and non-folding buttstock.

Instructions

AK-47 Strikeforce Stock Instructions 

Cheekrest Instructions

Share your thoughts!

4.76 out of 5 stars

66 review

What others are saying

  1. William Canaan

    Ak 12 gauge
    66

    by William Canaan (verified owner)

    I purchased this stock as a gift for my son to use on his SDS lynx 12 shotgun a good fit and rather intimidating looking 12 gauge. Thanks guys. Good job

    420439 (0) 420439 (0) 420439

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  2. Jonathan C.

    Folding stock
    66

    by Jonathan C. (verified owner)

    I like the stock. Instructions were not clear and not very easy to understand. The kit was also missing a screw. I noticed this when I installed the hand guard as well. Not a simple install but I like the way everything turned out.

    253137 (0) 253137 (0) 253137

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  3. Tim K.

    AK-47 Stock
    66

    by Tim K.

    Stock is excellent. Wood stock that came with the rifle was way too short. This ATI stock is so nice because it’s adjustable with a single finger. Exactly what I needed.

    253132 (0) 253132 (0) 253132

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  4. Jamey H.

    Like everything about your site
    66

    by Jamey H.

    Like everything about your site

    253124 (0) 253124 (0) 253124

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  5. Jordan H.

    A great improvement over the standard wood furniture. But some assembly is required.
    66

    by Jordan H.

    The only reason this set of furniture does not get 5 stars from me, is due to the amount of modification needed to get it all on. Now to preface this, I installed my set on a Wasr-10 and other models may fit the pieces better. To start the stock and pistol grip went on without a hitch, and on their own are a major improvement in comfort at the range. but the gas tube cover and front hand guard do need some modification to get on. The piece that goes on the gas tube will need to have both ends ground with a dremel at a angle to seat and twist in properly. not a big deal as they are still create a tight fit. as for the lower grip a small bit inside will need to be ground out, as well as some of the outer rear. This is due to the notch meant for seating in the gun in a bit to narrow, by cutting the outer part of and creating a near smooth shelf it will slot in with little issue. last bit is to sand the hole bits between the two to insure enough space to reattach the gas tube. once thats done you will have one of the most comfortable rifles I’ve had the pleasure of shooting. Hope this helps, its worth the money, but if you have a wasr preapare to spend an hour or two and some elbow grease it will be worth it.

    253122 (0) 253122 (0) 253122

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  6. RICHARD S.

    Total make over.
    66

    by RICHARD S.

    This is a great product just what the rifle needed,with a little grinding and trimming fits great.

    253125 (0) 253125 (0) 253125

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  7. Gilberto S.

    New look
    66

    by Gilberto S.

    I bought this to give my Ak a better look and I was not disappointed at all.

    253123 (0) 253123 (0) 253123

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  8. Guest

    Very tactical furniture! Riley ak47!
    66

    by Guest

    Very nice quality polymer upgrade for ak47. But here’s the thing this are not mill specs. Like the ar15 you have to pre fit this parts individually for your ak47. If your handy like me as a aerospace tech. I be able to grind & cut some of these pieces & fit snug just take your time you be able to make it work! Good Luck! Have fun!

    253120 (0) 253120 (0) 253120

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  9. Susan K.

    Great product
    66

    by Susan K.

    It was shipped fast, And more importantly, it fit perfectly in the Ak, Nice and tight.

    253121 (0) 253121 (0) 253121

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

  10. Michael S.

    Wonderful fit
    66

    by Michael S.

    Have seen many ATI retro fit kits for ruger 10/22 so I decided to try one for my AK, it went on with amazingly perfect fit. When I took it to the range it made the gun much lighter and much better fit for the shoulder. I highly recommend it to anyone that has a AK47 and wonts a more customized look and fit

    253119 (0) 253119 (0) 253119

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

×

Continue as a Guest

Don't have an account? Sign Up